濟南鐵藝大門是很多家庭喜歡用的，現在的別墅大門生產工藝已經不會很難，在市面上也可以看到有很多別墅庭院大門款式，但是別墅鐵藝大門安裝是一個難題，作為業主，了解別墅鐵藝大門安裝驗收標準，在驗收時才能知道別墅鐵藝大門安裝效果好不好，下面就來看看怎么安裝和驗收吧。

Villa iron gate is used by many families. Now the production process of villa gate is not very difficult. There are many villa courtyard gate styles in the market, but the installation of villa iron gate is a problem. As an owner, understand the installation and acceptance standards of villa iron gate, and you can know whether the installation effect of villa iron gate is good at the time of acceptance. Let's see how to install and accept it.

一、門套安裝

1、 Door pocket installation

1.門套安裝好后，在各連接地方應該是無縫隙、嚴密的。所有的固定配件都是緊固的，不會松動。門套對角線要準確，允許1.5mm以下的誤差。

1. After the door pocket is installed, the joints should be seamless and tight. All fixing accessories are fastened and will not loosen. The diagonal of the door pocket shall be accurate, and the error below 1.5mm is allowed.

2.門套的側框和橫框是水平垂直的，垂直側框允許公差+2mm，水平橫框公差允許+1mm；門套與墻體接合應該用固定螺釘，縫隙用發泡膠雙面密封，后期處理平整；如果門套寬度大于20出門，應該用到固定鐵片。

2. The side frame and transom of the door pocket are horizontal and vertical, the allowable tolerance of the vertical side frame is +2mm, and the tolerance of the horizontal transom is +1mm; The connection between the door pocket and the wall should be fixed with screws, and the gap should be sealed on both sides with styrofoam, and the post-treatment should be smooth; If the door pocket width is greater than 20, a fixed iron sheet should be used.

二、套線安裝

2、 Threading installation

安裝套線接口應該是沒有縫隙、嚴密、表面平整。套線與墻面縫隙也要用密封膠填好。

The installation socket should be seamless, tight and flat. The gap between the wiring and the wall should also be filled with sealant.

三、門扇安裝

3、 Door leaf installation

1.門扇方向要正確，開關比較靈活，沒有異常響聲。

1. The direction of the door leaf should be correct, and the switch should be flexible without abnormal sound.

2.門套與門扇之間留有縫隙，下面的大約6mm，與其他三面約為2mm，允許有0.5mm的差別。

2. There is a gap between the door pocket and the door leaf, which is about 6mm below and about 2mm from the other three sides, with a difference of 0.5mm allowed.

3.關上門后，門扇與密封條是緊密接合，沒有發生擺動。

3. After closing the door, the door leaf and the sealing strip are closely connected without swinging.

四、五金

4、 Hardware

1.門合頁應垂直、平整，在門適當的位置開槽，規范的做工，允許有0.5mm的差異，開始時合頁是正常靈活的，合頁固定螺釘要裝齊全，可以隱藏在合頁平面。

1. The door hinge should be vertical and flat, slotted at the appropriate position of the door, standard workmanship, allowing a difference of 0.5mm. At the beginning, the hinge is normal and flexible, and the hinge fixing screws should be installed completely, which can be hidden in the hinge plane.

2.門鎖開槽準確，方便日常的開啟，在關門開門上，鑰匙使用無明顯的異響，配件是安全的。

2. The slotting of the door lock is accurate and convenient for daily opening. When closing and opening the door, there is no obvious abnormal sound when using the key, and the accessories are safe.

3.緩沖、拉手、吸閉門器安裝在設計好的位置上，安裝牢固，保證配件使用效果是好的。

3. The buffer, handle and door closer shall be installed at the designed position and firmly installed to ensure the good use effect of accessories.

五、外觀

5、 Appearance

1.從整體外觀上，與地面接合的地方縫隙要在3mm以內，并用防水密封膠把縫隙密封好。

1. From the overall appearance, the gap at the joint with the ground should be within 3mm, and the gap should be sealed with waterproof sealant.

2.整個濟南鐵藝大門看起來沒有劃痕，做好清潔，視覺效果好。

2. The whole Jinan Tieyi gate looks free of scratches. It is clean and has good visual effect.

會減少別墅鐵藝大門的使用壽命。安裝結束后，在平時多注意別墅鐵藝大門保養，避免劃傷別墅鐵藝大門表面，讓別墅鐵藝大門使用年限更加久。更多相關事項就來我們網站http://www.cqf3.com咨詢了解。

It will reduce the service life of the iron gate of the villa. After installation, pay more attention to the maintenance of villa iron gate at ordinary times to avoid scratching the surface of villa iron gate and make the service life of villa iron gate longer. Come to our website for more related matters http://www.cqf3.com Consult and understand.